General norms for institutes for the conduct of

ANNEX – 13

(Level - 3 )
The following operational tasks that have to be complied with during workshop and of loads training at level – 3 by all institutions engaged in Marine engineering training.

Marine Oriented Work Shop

1. 
   Dismantling, overhauling, inspection & assembling of Centrifugal Pump.
   
2. 
   Dismantling, overhauling, inspection & assembling of a gear pump & screw pump
   
3. 
   Dismantling, overhauling, inspection & assembling of a reciprocating pump
   
4. 
   Dismantling, overhauling, inspection & assembling of variable displacement pump (swash plate)
   
5. 
   Dismantling, overhauling, inspection & assembling of sludge pump
   
6. 
   Dismantling, overhauling, inspection & assembling of a A/E Cyl. Head
   
7. 
   Dismantling, overhauling inspection & assembling of Cylinder liner, piston & piston ring
   
8. 
   Dismantling, overhauling, inspection & assembling of main bearing & bottom end bearing.
   
9. 
   C/Shaft deflection & inspection of C/case
   
10. 
    Dismantling overhauling & testing of fuel injector.
    
11. 
    Dismantling & overhauling of M/E exhaust valve.
    
12. 
    Dismantling & overhauling of M/E cylinder head relief v/v, Air staring v/v.
    
13. 
    Dismantling & overhauling of Turbochargers.
    
14. 
    Dismantling, overhauling, inspection & & assembling of Air Compressor.
    
15. 
    Dismantling , overhauling, inspection & assembling of purifier.
    
16. 
    Inspection & overhauling of air bottle, mountings.
    
17. 
    Working principles & demonstration of working of a hydraulic steering gear system, safety checks & routine inspection
    
18. 
    Dismantling , overhauling, inspection & assembling of shell & tube type cooler.
    
19. 
    Dismantling , overhauling, inspection & assembling of plate type cooler.
    
20. 
    Operation & working principles of F.W. Generator & Reverse osmosis system.
    
21. 
    Operation & working principles of oily water separator
    
22. 
    Overhauling inspection & assembling of Boiler safety v/v.
    
23. 
    Overhauling inspection & assembling of feed check v/v
    
24. 
    Overhauling inspection & assembling gauze glass.
    
25. 
    To fabricate & weld a pipe with given pipe length & flanges.
    
26. 
    To repair a leaks pipe by fitting a dubbler.
    
27. 
    To make a pipe line with bends (welding)
    
28. 
    To dismantle, inspection & overhaul a hydraulic pp for deck crane.
    
29. 
    Practice of welding.
    
30. 
    Practice of Brazing & Soldering
    
31. 
    Detection of cracks & dealing with cracked pieces
    
32. 
    L.O. & fuel oil testing
    
33. 
    Tracing of pipelines.
    

Using Turbo Diesel the Following experiments are to be performed

1. 
   To start and stop the engine,
   
2. 
   To change engine’s load and speed
   
3. 
   To change ambient operating conditions
   
4. 
   To simulate engine faults in varying degrees
   
5. 
   To mix different simulations
   
6. 
   To watch engine operation parameters
   
7. 
   To watch functions inside the dylinder
   
8. 
   To simulate the engine sound which varies with speed
   
9. 
   To carry out maintenance and repairs
   
10. 
    To try out different maintenance strategies
    
11. 
    To print engine data
    
12. 
    To sue lesson facility