Specifications

TOILET ACCESSORIES SECTION 10800

PART 1 GENERAL

1.1 REFERENCES

The publications listed below form a part of this specification to the extent referenced. The publications are referred to in the text by basic designation only.

COMMERCIAL ITEM DESCRIPTIONS (CID)

CID A-A-2380 (Basic) Dispenser, Paper Towel

CID A-A-2668 (Basic) Dispenser, toilet Paper

FEDERAL S PECIFICATIONS (FS)

FS W-H- 50 (Rev.B; Am 1, Notice 1) Hand Drier, Blower,

Electric

FS WW-P-541/GEN (Rev E; Am 1) Plumbing Fixtures

FS WW-P-541/8 (Rev B; Am 1) Plumbing Fixtures (Accessories,

Land Use)

1.2 SUBMITTALS

Government approval is required for submittals with a "GA" designation, submittals having an "FIO" designation are for information only. The following shall be submitted in accordance with Section C-01300 SUBMITTAL PROCEDURES:

SD-01 Data

Finishes; FIO.

Accessory Items; GA.

Manufacturer's descriptive data and catalog cuts indicating materials of construction, fasteners proposed for use for each type of wall construction, mounting instructions, and operation

instructions.

SD-14 Samples

Finishes; GA.

Accessory Items; GA.

One sample of each accessory proposed for use. Approved samples may be incorporated into the finished work, provided they are identified and their locations noted.

SD-19 Operation and Maintenance Manuals

Electric Hand Dryer; GA.

Four complete copies of maintenance instructions listing routine maintenance procedures and possible breakdowns and repairs. Instructions shall include simplified wiring and control diagrams and other information necessary for unit maintenance.

1.3 DELIVERY, STORAGE, AND HANDLING

Toilet accessories shall be wrapped for shipment and storage, delivered to the jobsite in manufacturer's original packaging and stored in a clean, dry area protected from construction damage and vandalism.

1.4 GENERAL REQUIREMENTS

Toilet accessories as specified herein shall be provided where indicated in accordance with paragraph "SCHEDULE." Each accessory item shall be complete with the necessary mounting plates, anchors, and fasteners. Concealed mounting plates shall be of sturdy construction with corrosion resistant surface.

1.4.1 Anchors and Fasteners

Anchors and fasteners shall be capable of developing a restraining force commensurate with the strength of the accessory to be mounted and shall be well suited for use with the supporting construction. Where exposed fasteners are permitted, they shall have oval heads and finish to match the accessory.

PART 2 PRODUCTS

2.1 MANUFACTURED UNITS

Toilet accessories shall be provided where indicated on drawings. Each accessory item shall be complete with the necessary mounting plates, shall be of sturdy construction with corrosion resistant surface.

2.1.1 Anchors and Fasteners

Anchors and fasteners shall be capable of developing a restraining force commensurate with the strength of the accessory to be mounted and shall be suited for use with the supporting construction. Exposed fasteners shall be of tamperproof design and shall be finished to match the accessory.

2.1.2 Finishes

Finishes on metal shall be provided as follows:

Metal Finish

Stainless steel No. 4 satin finish

Carbon steel, copper alloy, Chromium plated, bright and brass

2.2 ACCESSORY ITEMS

Accessory items shall conform to the requirements specified below.

All accessories shall have a smooth finish.

2.2.1 Not Used

2.2.2 Grab Bar

Grab bar shall conform to FS WW-P-541/GEN and FS WW-P-541/8, Type IV, Class 2, 38 mm OD stainless steel. Grab bar shall be form and length as indicated. Concealed mounting flange shall have set screw-mounting holes concealed on the lip of the flange. Grab bar shall have a smooth finish. Installed bars shall be capable of withstanding a 2.225 kN vertical load without coming loose from the fastenings and without obvious permanent deformation.

2.2.2.1 (Item No. 1): Grab bar 900 mm long

2.2.2.2 (Item No. 2): Grab bar 1200 mm long

2.2.3 Not Used

2.2.4 Mirror, Glass

2.2.4.1 (Item No. 12): Refer to Section C-08810 for metal framed mirror.

2.2.4.2 (Item No. 13): Refer to Section C-08810 for frameless mirrors.

2.2.5 Not Used

2.2.6 Not Used

2.2.7 Not Used

2.2.8 Combination Paper Towel Dispenser/Waste Receptacle Units (Item No. 10)

Roll paper towel dispenser/receptacle shall be semi-recessed and shall accept 38 mm core diameter rolls 203 mm wide x 244 m long. Waste receptacle shall be designed to be locked in unit and removable for service. Locking mechanism shall be tumbler key lock. Waste receptacle shall have a capacity of 32.6 L. Unit shall be fabricated of not less than 1.2 mm stainless steel welded construction with all exposed surfaces having a satin finish. Waste receptacle that accepts reusable liner standard for unit manufacturer shall be provided.

2.2.8.1 Dimensions (rough wall opening): 368 mm wide x 1006 mm high x 89 mm minimum recessed depth.

2.2.8.2 The roll paper towel dispenser/waste receptacle unit listed is for identification purposes only; the product listed is not intended to limit selection of a similar product from other manufacturers.

2.2.8.3 Product/Manufacturer: B-396034/Bobrick

2.2.9 Not Used

2.2.10 Sanitary Napkin and Tampon Dispenser with Door (Item No. 6)

Sanitary napkin and tampon dispenser shall conform to FS WW-P-541/GEN and FS WW-P-541/8, Type I, Class 5, recess mounted.

Dispenser, including door shall be Type 304 stainless steel and shall have a capacity of 31 napkins and 22 tampons. Dispensing mechanism shall be for coin operation. Coin mechanisms shall be field changeable by adjusting pins for new coin designation. Coin mechanisms shall have minimum denominations of 50 cents and free.

2.2.10.1 Dimensions (rough wall opening): 384 mm wide x 650 mm high x 105 mm minimum recessed depth.

2.2.10.2 The sanitary napkin and tampon dispenser listed is for identification purposes only; the product listed is not intended to limit selection of a similar product from other manufacturers.

2.2.10.3 Product/Manufacturer: B3500X2/Bobrick

2.2.11 Not Used

2.2.12 Not Used

2.2.13 Soap Dispenser (Item No. 13)

2.2.13.1 Manufacturers names and design of undercounter multilavatory soap reservoir indicated are for identifying purposes only and are not intended to limit selection of similar products by other manufacturers.

2.2.13.2 Soap dispenser shall be liquid type consisting of an undercounter, multi-lavatory soap reservoir of sufficient size to provide a minimum of 1 L per dispenser with a corrosion-resistant all-purpose valve that dispenses liquid soap, lotions, detergents, and antiseptic soap. Stainless steel piston and 103 mm spout, operation shall require less than 22.2 N of force.

2.2.13.3 Product/Manufacturer: Countura Series Lavatory mounted Soap Dispenser with Under-the-Counter Soap Reservoir B-922/Bobrick

Washroom Equipment

2.2.14 Not Used

2.2.15 Not Used

2.2.16 Not Used

2.2.17 Not Used

2.2.18 Not Used

2.2.19 Not Used

2.2.20 Not Used

2.2.21 Not Used

2.2.22 Not Used

2.2.23 Not Used

2.2.24 Electric Hand Dryer (Item No. 9)

Electric hand dryer shall conform to FS W-H-50 and shall be wall mounted and shall be designed to operate on 115 volts, 60 cycle, single phase alternating current with a heating element core rating of not more than 1725 watts. Dryer housing shall be of single piece construction and shall have a cover of 3 mm thick fireretardant molded ABS with a high-gloss white finish.

2.2.24.1 The electric hand dryer listed is for identification purposes only; the product listed is not intended to limit selection of a similar product from other manufacturers.

2.2.24.2 Product/Manufacturer: B710/Bobrick

2.2.25 Not Used

2.2.26 Toilet-Seat-Cover Dispenser, Sanitary Napkin Disposal, and Toilet Tissue Dispenser

2.2.26.1 The listed toilet-seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser are for identification purposes only; the product listed is not intended to limit selection of a similar product from other manufacturers.

2.2.26.2 Recessed Model (Item No. 3)

Toilet-seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser shall be recess mounted, handicapped accessible. The unit shall be of type 304 stainless steel. The toilet-seat

cover dispenser shall have a capacity of 1,000 paper toilet seat covers and shall be covered with a door equipped with a tumbler lock. Sanitary napkin disposal shall be furnished with a removable

stainless steel receptacle with a capacity if 5.7 L. The sanitary napkin disposal shall be covered with a door equipped with a tumbler lock. The unit shall have two chrome plated plastic toilet

tissue spindles that hold standard core rolls up to 130 mm diameter (1500 sheets).

a) Dimensions (rough wall opening): 406 mm wide x 743 mm high x 102 mm minimum recess depth.

b) Product/Manufacturer: B-3574.60/Bobrick

2.2.26.3 Partition Mounted (Serves Two Toilet Compartments) (Item No. 4)

Toilet-seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser shall be partition mounted. The unit shall be of type 304 stainless steel. The toilet-seat cover dispenser shall

have a capacity of 1,000 paper toilet seat covers and shall be covered with a door equipped with a tumbler lock. Sanitary napkin disposal shall be furnished with a removable stainless steel receptacle with a capacity if 5.7 L. The sanitary napkin disposal shall be covered with a door equipped with a tumbler lock. The unit shall have two chrome plated plastic toilet tissue spindles

that hold standard core rolls up to 115 mm diameter (1000 sheets), two for each compartment.

a) Product/Manufacturer: B-357.60/Bobrick

2.2.26.4 Surface Mounted Model (Item No. 5)

Toilet-seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser shall be surface mounted. The unit shall be of type 304 stainless steel. The toilet-seat cover dispenser shall have a capacity of 1,000 paper toilet seat covers and shall be covered with a door equipped with a tumbler lock. Sanitary napkin disposal shall be furnished with a removable stainless steel receptacle with a capacity if 5.7 L. The sanitary napkin disposal shall be covered with a door equipped with a tumbler lock. The unit shall have two chrome plated plastic toilet tissue spindles that hold standard core rolls up to 130 mm diameter (1500 sheets).

a) Product/Manufacturer: B-3579.60/Bobrick

2.2.27 Toilet-Seat-Cover and Toilet Tissue Dispenser

2.2.27.1 The toilet-seat-cover and toilet tissue dispenser listed are for identification purposes only; the product listed is not intended to limit selection of a similar product from other manufacturers.

2.2.27.2 Recessed Model (Item No. 7)

Toilet-seat-cover dispenser and toilet tissue dispenser shall be recess mounted, handicapped accessible. The unit shall be of type 304 stainless steel. The toilet-seat cover dispenser shall have a capacity of 1,000 paper toilet seat covers and shall be covered with a door equipped with a tumbler lock. Sanitary napkin disposal shall be furnished with a removable stainless steel receptacle with a capacity if 5.7 L. The sanitary napkin disposal shall be covered with a door equipped with a tumbler lock. The unit shall have two chrome plated plastic toilet tissue spindles that hold standard core rolls up to 130 mm diameter (1500 sheets).

a) Dimensions (rough wall opening): 406 mm wide x 743 mm high x 102 mm minimum recess depth.

b) Product/Manufacturer: B-3474.60/Bobrick

2.2.27.3 Surface Mounted Model (Item No. 8)

Toilet-seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser shall be surface mounted. The unit shall be of type 304 stainless steel. The toilet-seat cover dispenser shall have a capacity of 1,000 paper toilet seat covers and shall be covered with a door equipped with a tumbler lock. Sanitary napkin disposal shall be furnished with a removable stainless steel receptacle with a capacity if 5.7 L. The sanitary napkin disposal shall be covered with a door equipped with a tumbler lock. The unit shall have two chrome plated plastic toilet tissue spindles that hold standard core rolls up to 130 mm diameter (1500 sheets).

a) Product/Manufacturer: B-3479.60/Bobrick

PART 3 EXECUTION

3.1 INSTALLATION

Toilet accessories shall be securely fastened to the supporting construction in accordance with the manufacturer's approved instructions. Accessories shall be protected from damage from the

time of installation until acceptance.

-- END OF SECTION --

Minimum Submittals:

1. 
   Site Survey.
   
2. 
   Site Layout of Trailers, Utility Lines, Water Tank, Septic Tank, and, Warehouse.
   
3. 
   Electrical Power distribution schematic / single line diagram.
   
4. 
   Grounding System for all structures.
   
5. 
   Foundations.
   
6. 
   Warehouse steel structure.
   
7. 
   Warehouse foundation plan.
   
8. 
   Trailers and Latrine Trailer layout / floor plan.
   
9. 
   Trailers and Latrine Trailer Structural Plan.
   
10. 
    Exterior and Interior Doors.
    
11. 
    Interior Electric for Warehouse and Trailers.
    
12. 
    Power distribution panels and transformers.
    
13. 
    Pumps, valves, controls, schematics.
    
14. 
    Trailers’ walls w/ insulation and roofing w/ insulation.
    
15. 
    Power distribution cables sizes and types.
    
16. 
    Telecommunications cable sizes and types.
    
17. 
    Fire Panels.
    
18. 
    Interior lights and exterior lights, and exit signs.
    
19. 
    Reflected ceiling plan.
    
20. 
    HVAC Split-Units.
    
21. 
    Water Tank and supporting structure.
    
22. 
    Septic Tank, including “dead-man” to hold the septic tank down into the ground.
    
23. 
    Sewer piping and schematic.
    
24. 
    Water piping and schematic.
    
25. 
    Toilets, Sinks, Shower piping and heads, sink shelves.
    
26. 
    Concrete test results.
    
27. 
    Megger test results.
    

Warehouse Floor Plan (Min. 49 meters x 15 meters x 4.5 meters high)

TRAILER # 1

TRAILER #2



LATRINE # 1


LATRINE # 2

Attachment 1 – F3XXXX-05-R-XXXX 17 Dec 2004